Conductive Polymer Research Articles

Electrocatalytic Poly(3,4-ethylenedioxythiophene) for Electrochemical Conversion of 5-Hydroxymethylfurfural.

This study investigates the utilization of the conductive polymer poly(3,4-ethylenedioxythiophene) (PEDOT) as a catalytic material for the 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-mediated oxidation of 5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid (FDCA). PEDOT films doped with different counterions were electrodeposited on graphite foil. In particular, the mobile anion perchlorate and the polymeric ionomers polystyrenesulfonate, Nafion, and Aquivion were used. The electrocatalytic properties of PEDOT films were evaluated toward the TEMPO redox mediator in the absence and the presence of HMF as a substrate for oxidation reactions. The electrocatalytic HMF oxidation was confirmed to occur at PEDOT electrodes, and it was also found that the chemical nature of PEDOT counterions controls the electrocatalytic conversion of HMF by modulating the kinetics of the electrochemical generation of the oxoammonium cation TEMPO(+). Potentiostatic electrolysis experiments showed that both the reference graphite electrode and PEDOT substrates were able to convert HMF to FDCA with an 80% faradaic efficiency (FE) and a >90% yield (FDCA), but, compared to graphite, the complete conversion of HMF to FDCA required a ca. 30% shorter time when using PEDOT electrodes doped with perchlorate or Aquivion, thanks to their ability to sustain a higher current density in the initial phase of the electrolysis. In addition, while all PEDOT films were chemically stable under the electrochemical conditions herein described, only PEDOT films doped with Aquivion were also mechanically robust and stable against delamination. Thus, the new PEDOT/Aquivion composite may represent the best choice for the implementation of PEDOT-based electrodes in TEMPO-mediated electrocatalytic applications.

Conductive MXene/Polymer Composites for Transparent Flexible Supercapacitors.

Transparent flexible energy storage devices are limited by the trade-off among flexibility, transparency, and charge storage capability of their electrode materials. Conductive polymers are intrinsically flexible, but limited by small capacitance. Pseudocapacitive MXene provides high capacitance, yet their opaque and brittle nature hinders their flexibility and transparency. Herein, the development of synergistically interacting conductive polymer Ti3C2Tx MXene/PEDOT:PSS composites is reported for transparent flexible all-solid-state supercapacitors, with an outstanding areal capacitance of 3.1 mFcm-2, a high optical transparency of 61.6%, and excellent flexibility and durability. The high capacitance and high transparency of the devices stem from the uniform and thorough blending of PEDOT:PSS and Ti3C2Tx, which is associated with the formation of O─H…O H-bonds in the composites. The conductive MXene/polymer composite electrodes demonstrate a rational means to achieve high-capacity, transparent and flexible supercapacitors in an easy and scalable manner.

Conductive Polypyrrole: Synthesis, Characterization, Thermal, and Electrical Properties for different applications

Abstract Pyrrole monomer (mPPy) in an aqueous solution was used to create the conductive polymer polypyrrole (a homo-PPy) using a chemical oxidative polymerization process over a period of several hours at room temperature. Ferric chloride (FeCl3) oxidant was used, and sodium dodecyl sulphate (C12H25NaO4S), a surfactant. The produced PPy samples were characterized using a variety of methods, including X-ray diffraction (XRD), the Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), Differential Thermal analysis (DTA), Thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). SEM images revealed that nanoparticles of a homo-PPy with radii of 60-90 nm were well evenly distributed in the structure. The thermal stability and electrical conductivity of homo-PPy nanoparticles were observed to rise with a different solvent content of homo-PPy nanoparticles. As temperature rises, the electrical resistivity of the FeCl3 oxidation decreases, resulting in enhanced conductivity. It has been noted that the conductivity of homo-PPy samples is 
 significantly influenced by their shape, and electrical conductivities ranging from.0.44 to 2.2 (Ω.m)-1. It was revealed that the solvent (ethylene glycol) and monomer had more successful heat stability. Results from FTIR and XRD analysis confirmed the structural formation of a homo-polypyrrole during synthesis from pyrrole monomer. Because of their improved electrical conductivity and thermal stability, homo-PPy nanoparticles have potential applications in energy storage, adsorption and contamination elimination, electromagnetic protection, and resistance to corrosion.

A reconfigurable integrated smart device for real-time monitoring and synergistic treatment of rheumatoid arthritis.

Rheumatoid arthritis (RA) is a global autoimmune disease that requires long-term management. Ambulatory monitoring and treatment of RA favors remission and rehabilitation. Here, we developed a wearable reconfigurable integrated smart device (ISD) for real-time inflammatory monitoring and synergistic therapy of RA. The device establishes an electrical-coupling and substance delivery interfaces with the skin through template-free conductive polymer microneedles that exhibit high capacitance, low impedance, and appropriate mechanical properties. The reconfigurable electronics drive the microneedle-skin interfaces to monitor tissue impedance and on-demand drug delivery. Studies in vitro demonstrated the anti-inflammatory effect of electrical stimulation on macrophages and revealed the molecular mechanism. In a rodent model, impedance sensing was validated to hint inflammation condition and facilitate diagnosis through machine learning model. The outcome of subsequent synergistic therapy showed notable relief of symptoms, elimination of synovial inflammation, and avoidance of bone destruction.

Detectable quorum signaling molecule via PANI-metal oxides nanocomposites sensors.

The detection of N-hexanoyl-l-homoserine lactone (C6-HSL), a crucial signal in Gram-negative bacterial communication, is essential for addressing microbiologically influenced corrosion (MIC) induced by sulfate-reducing bacteria (SRB) in oil and gas industries. Metal oxides (MOx) intercalated into conducting polymers (CPs) offer a promising sensing approach due to their effective detection of biological molecules such as C6-HSL. In this study, we synthesized and characterized two MOx/polyaniline-dodecyl benzene sulfonic acid (PANI-DBSA) nanocomposites, namely ZnO/PANI-DBSA and Fe2O3/PANI-DBSA. These nanocomposites were applied with 1% by-weight carbon paste over a carbon working electrode (WE) for qualitative and quantitative detection of C6-HSL through electrochemical analysis. The electrochemical impedance spectroscopy (EIS) confirmed the composites' capability to monitor C6-HSL produced by SRB-biofilm, with detection limits of 624 ppm for ZnO/PANI-DBSA and 441 ppm for Fe2O3/PANI-DBSA. Furthermore, calorimetric measurements validated the presence of SRB-biofilm, supporting the EIS analysis. The utilization of these MOx/CP nanocomposites offers a practical approach for detecting C6-HSL and monitoring SRB-biofilm formation, aiding in MIC management in oil and gas wells. The ZnO/PANI-DBSA-based sensor exhibited higher sensitivity towards C6-HSL compared to Fe2O3/PANI-DBSA, indicating its potential for enhanced detection capabilities in this context. Stability tests revealed ZnO/PANI-DBSA's superior stability over Fe2O3/PANI-DBSA, with both sensors retaining approximately 85-90% of their initial current after 1month, demonstrating remarkable reproducibility and durability.

Engineering Interconnected Nanofluidic Channel in a Hydrogel Supernetwork toward K+ Ion Accelerating Transport and Efficient Sensing.

Ion transportation via the mixed mechanisms of hydrogels underpins ultrafast biological signal transmission in nature, and its application to the rapid and sensitive sensing detection of human specific ions is of great interest for the field of medical science. However, current research efforts are still unable to achieve transmission results that are comparable to those of bioelectric signals. Herein, 3D interconnected nanochannels based on poly(pyrrole-co-dopamine)/poly(vinyl alcohol) (P(Py-co-DA)/PVA) supernetwork conductive hydrogels are designed and fabricated as stimuli-responsive structures for K+ ions. Distinct from conventional configurations, which exhibit rapid electron transfer and permeability to biosubstrates, interconnected nanofluidic nanochannels collaborated with the P(Py-co-DA) conductive polymer in the supernetwork conductive hydrogel significantly improve conductivity (88.3 mS/cm), ion transport time (0.1 s), and ion sensitivity (74.6 mV/dec). The faster ion response time is attributed to the synergism of excellent conductivity originating from the P(Py-co-DA) polymer and the electronic effect in the interconnected nanofluidic channels. Furthermore, the supernetwork conductive hydrogel demonstrates K+ ion selectivity relative to other cations in biofluids such as Na+, Mg2+, and Ca2+. The DFT calculation indicates that the small solvation energy and low chemical transfer resistance are the main reasons for the excellent K+ ion selectivity. Finite element analysis (FEA) simulations further support these experimental results. Consequently, the P(Py-co-DA)/PVA supernetwork conductive hydrogels enriched with the 3D interconnected nanofluidic channels developed in this work possess excellent sensing of K+ ions. This strategy provides great insight into efficient ion sensing in traditional biomedical sensing that has not been explored by previous researchers.

Thermally Induced Phase Separation of the PEDOT:PSS Layer for Highly Efficient Laminated Polymer Light-Emitting Diodes.

Among various conductive polymers, the poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) film has been studied as a promising material for use as a transparent electrode and a hole-injecting layer in organic optoelectronic devices. Due to the increasing demand for the low-cost fabrication of organic light-emitting diodes (OLEDs), PEDOT:PSS has been employed as the top electrode by using the coating or lamination method. Herein, a facile method is reported for the fabrication of highly efficient polymer light-emitting diodes (PLEDs) based on a laminated transparent electrode (LTE) consisting of successive PEDOT:PSS and silver-nanowire (AgNW) layers. In particular, thermally induced phase separation (TIPS) of the PEDOT:PSS film is found to depend on the annealing temperature (Tanneal) during preparation of the LTE. At Tanneal close to the glass transition temperature of the PSS chains, a PSS-rich phase with a large number of PSS- molecules enhances the work function of the PEDOT:PSS on the glass-side surface relative to the air side. By using the optimized LTEs, bidirectional laminated PLEDs are obtained with a total external quantum efficiency of 2.9% and a turn-on voltage of 2.6 V, giving a comparable performance to that of the reference bottom-emitting PLED based on a costly evaporated metal electrode. In addition, an analysis of the angular characteristics, including the variation in the electroluminescence spectra and the change in luminance according to the emission angle, indicates that the laminated PLED with the LTE provides a more uniform angular distribution regardless of the direction of emission. Detailed optical and electrical analyses are also performed to evaluate the suitability of LTEs for the low-cost fabrication of efficient PLEDs.

Thermal and hydraulic performance of volumetrically heated triply periodic minimal surface heaters

Advanced heat transfer surfaces, mainly Triply Periodic Minimal Surfaces (TPMSs) have great potential to increase heat transfer performance over traditional heat transfer surfaces due to their tortuous flow path and higher surface area-volume ratio. The emergence of additive manufacturing of nuclear fuel motivates experimental investigation of such advanced geometries in the context of a nuclear reactor core. This study employed a novel method to explore the performance of gyroid and diamond TPMS geometries. Volumetrically heated heaters were additively manufactured from conductive polymer filament, and airflow was used to simulate the convective heat transfer from the core within a nuclear reactor. The mass flow and volumetric generation rates were varied, local Nusselt number correlations were obtained using embedded thermocouples to measure the solid and fluid temperature, and friction factor correlations were developed using differential pressure measurements. The gyroid TPMS presented a friction factor 1.5 times higher than the diamond TPMS and 90 times that of the rod bundle. TPMS geometries showed Nusselt numbers 8–10 times higher than that of the rod bundle, also maintaining colder internal temperatures, which suggested that they could sustain 250–275 % higher power density than the rod bundle for a given centerline temperature. Hence, having the potential to greatly increase the safety margins and power output of a nuclear reactor core with similar volume.

Enhancing the attraction of positively charged precursors of conductive polymer poly(3,4-ethylenedioxythiophene) by anchoring sulfonate groups in cellulose fibres

Enhancing the attraction of positively charged precursors of conductive polymer poly(3,4-ethylenedioxythiophene) by anchoring sulfonate groups in cellulose fibres

Synthesis and Characterization of PVA/PANI Nanofiber as Active Material for Humidity Sensors

PANI is a nanostructure conductive polymer that has been widely researched by making nanofibers using electrospinning, by adding PVA as a non-conductive material. In this research, we have successfully synthesized PVA/PANI nanofiber using the electrospinning method and applied it as a humidity sensor. The oxidation polymerization method was conducted to produce polyaniline (PANI) powder. PVA was used as a non-conductive polymer to carry PANI. PANI is blended with 10 % PVA to produce nanofiber PVA/PANI. The results of the synthesis of PVA/PANI nanofibers using the electrospinning method have been characterized by FTIR and EDX to identify the functional groups and elements of PVA/PANI. The FTIR results confirmed that for the PVA nanofiber samples, the type of polyvinyl alcohol bond has been identified according to the reference. The EDX results show the elements C, O and N. The element nitrogen (N) is the characteristic element of polyaniline (C6H5(NH)2)n. The optical Microscope and Scanning Electron Microscope show that the electrospinning method has succeeded in synthesizing PVA/PANI nanofibers with a fiber size of around 0.313 mm. The porosity of PVA/PANI is around 55 %, which is related to the ability of PVA/PANI sensitivity to detect humidity. These results are demonstrated by measurements using a Four-Point Probe (FPP), with the humidity value varying from 64 - 80 %. The results show that variations of PANI powder content improve the sensitivity performance of PVA/PANI nanofibers. This method can optimize PVA/PANI nanofiber as a humidity sensor, increase conductivity flexibility, make it easier and enhance the PANI to use as an active sensor. HIGHLIGHTS The active material for the sensor is polyaniline-based. Polyaniline oxidation polymerization using a method with solid acid doping, which can increase the conductivity of polyaniline (PANI). The formation of PANI nanofibers increases the sensing activities’ effectiveness. Polyvinyl alcohol (PVA) is used as a carrier to facilitate the synthesis process by electrospinning. GRAPHICAL ABSTRACT

Enhanced pseudocapacitance performance of conductive polymer in the presence of synthesized mesoporous MnO2@Zeolite-Y

In the current study, mesoporous MnO2@Zeolite-Y (MOZ) was synthesized using the ultrasonic method. Then, MOZ was utilized to enhance the electrochemical behavior of poly ortho-aminophenol (POAP) conducting polymer. The POAP/MnO2@Zeolite-Y (MOZ/POAP) composite was synthesized by electropolymerization over the zeolite-modified working electrode surface. To investigate and compare the electrochemical behavior of the synthesized materials, two electrodes of MOZ and MOZ/POAP were designed. Subsequently, the electrochemical characteristics of the two mentioned electroactive compounds were evaluated by galvanostatic charge/discharge (GCD), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) tests in a three-electrode setup. The comparison of the results revealed that the MOZ/POAP electrode had a more significant performance and recorded a specific capacitance (Cs) of 422 F g−1 at 1 A g−1 and cyclic stability of 97.2 % over 10,000 cycles. After verifying this electrode's remarkable efficacy, a symmetric supercapacitor of MOZ/POAP was designed and analyzed by CV and GCD techniques in a two-electrode system. This electrode revealed a Cs of 184 F g−1 at 1 A g−1, energy density of 12.02 Wh kg−1, power density of 275 W kg−1, and cyclic stability of 95.7 % over 10,000 cycles. This impressive performance was due to the presence of the manganese metal in MOZ and nitrogen and oxygen species of POAP in improving the pseudocapacitance behavior, POAP as a conductive chemical and mesoporous zeolite-Y for enhancing the electrical double-layer behavior of the electrode by providing a medium for electrochemical reactions.

Effect of 1 wt% Dimethyl Sulfoxide on the Electrical and Photovoltaic Parameters of Schottky Diodes and Organic Solar Cells Based on PEDOT:PSS

Herein, the electrical conductivity of poly(3,4‐ethylenedioxythiophene)–poly(styrenesulfonate) (PEDOT:PSS) polymer is improved by adding dimethyl sulfoxide (DMSO) and electrical characterization of the obtained Schottky diode and organic solar cell (OSC) devices are performed from I–V measurements under the light and dark conditions. The scanning electron microscope images of the poly(3‐hexylthiophene):[6,6]‐phenylC61‐butyric acid methylester active layer and PEDOT:PSS layer are obtained. The series resistance (Rs), barrier height (Фb), and ideality factor (n) parameters are obtained from different techniques as a function of light and dark conditions. Furthermore, photovoltaic parameters are calculated for n‐Si/PEDOT:PSS/Au device without DMSO doping and with DMSO doping as a parameter of the light condition and the interface state densities of these devices are obtained for light and dark conditions. DMSO organic solvent improves the short‐circuit current density (Isc), power convert efficiency (or η), open circuit‐voltage (Voc), shunt resistance (Rsh), and series resistance (Rs) values of OSCs. In summary, DMSO solvent rearranges the conductive of PEDOT:PSS, decreases the work function of this conductive polymer (≈5 eV), decreases energy loss in the charge transportation, and increases photovoltaic parameters of Schottky barrier diode and OSC devices.

Recent Advances in the Strategies of Simultaneous Enzyme Immobilization Accompanied by Nanocarrier Synthesis

In recent years, with advancements in nanotechnology and materials science, new enzyme immobilization strategies based on nanomaterials have continuously emerged. These strategies have shown significant effects on enhancing enzyme catalytic performance and stability due to their high surface area, good chemical stability, and ease of enzyme binding, demonstrating tremendous potential for industrial applications. Those methods that can rapidly synthesize nanocarriers under mild conditions allow for the one-step synthesis of nanocarriers and enzyme complexes, thereby exhibiting advantages such as simplicity of process, minimal enzyme damage, short processing times, and environmental friendliness. This paper provides an overview of simultaneous enzyme immobilization strategies accompanied by nanocarrier synthesis, including organic–inorganic hybrid nano-flowers (HNFs), metal–organic frameworks (MOFs), and conductive polymers (CPs). It covers their preparation principles, post-immobilization performance, applications, and existing challenges.

Copolymers of Gelatin-graft-poly(3-hexylthiophene) for Transient Electronics.

As transient electronics continue to advance, the demand for new materials has given rise to the exploration of conducting polymer (CP)-based electronic materials. The big challenge lies in balancing conductivity while introducing controlled degradable properties into CP-based transient materials. In response to this, we present in this work a concept of using conducting polymers attached to an enzymatically biodegradable biopolymer to create transient polymer electronics materials. Specifically, poly(3-hexyl thiophene) (P3HT) is covalently grafted onto biopolymer gelatin, affording graft copolymer gelatin-graft-poly(3-hexyl thiophene) (termed Gel-g-P3HT). The thin films of Gel-g-P3HT that were produced by optimized processing solvent (THF/H2O cosolvent) showed enhanced π-π stacking domains of P3HT, resulting in semiconducting thin films with good electroactivity. Due to the presence of amide bonds in the gelatin backbone, Gel-g-P3HT underwent degradation over a period of 5 days, resulting in the formation of amphiphilic micellar nanoparticles that are biocompatible and nontoxic. The potential of these conductive and degradable graft copolymers was demonstrated in a pressure sensor. This research paves the way for developing biocompatible and enzymatically degradable polymer materials based on P3HT, enabling the next generation of transient polymer electronics for diverse applications, such as skin, implantable, and environmental electronics.

Enhancing the Conductivity and Thermoelectric Performance of Semicrystalline Conducting Polymers Through Controlled Tie Chain Incorporation.

Conjugated polymers are promising materials for thermoelectric applications, however, at present few effective and well understood strategies exist to further advance their thermoelectric performance. Here we report a new model system for better understanding the key factors governing their thermoelectric properties: aligned, ribbon-phase poly[2,5-bis(3-dodecylthiophen-2-yl)thieno[3,2-b]thiophene] (PBTTT) doped by ion-exchange doping. Using a range of microstructural and spectroscopic methods we study the effect of controlled incorporation of tie-chains between the crystalline domains through blending of high and low molecular weight chains. The tie chains provide efficient transport pathways between crystalline domains and lead to significantly enhanced electrical conductivity of 4810.1 S/cm, that is not accompanied by a reduction in Seebeck coefficient nor a large increase in thermal conductivity. We demonstrate respectable power factors of 172.6 µW m-1 K-2 in this model system. Our approach is generally applicable to a wide range of semicrystalline conjugated polymers and could provide an effective pathway for further enhancing their thermoelectric properties and overcome traditional trade-offs in optimization of thermoelectric performance. This article is protected by copyright. All rights reserved.

Growth of CQD/PPy on cotton cloth as a binder-free high-performance flexible electrode for symmetric supercapacitor

Benefited from the continuous development of nanomaterials, wearable microelectronics with flexible and miniaturized features are booming, and smart textiles are attracting more attentions because of their superior flexibility and perfect safety. The combination of conductive polymers and flexible substrates has created a new field for flexible supercapacitors. Herein, cotton cloth (CC), which is commonly used in daily life, was selected as the flexible substrate and a layer of CQDs was uniformly grown on the CC fibers, and then pyrrole was directly grown on CC by in-situ polymerization under Fe3+ initiation to realize the tight bonding between the conductive polymer and the flexible substrate. The electrochemical properties of the composite electrode could be controlled by changing the amount of CQD. The obtained CC@CQD@PPy electrode has a high specific capacitance (C) of 537.9 F/g at 0.5 A/g. The assembled symmetric CC@CQD@PPy supercapacitor exhibits an excellent energy density (E) of 18.7 Wh/kg at a power density (P) of 125.0 W/kg, and a supreme cycling stability with a capacitance retention of 77.9 % after 10,000 cycles. In addition, the CC@CQD@PPy supercapacitor has excellent flexibility, with almost unchanged electrochemical performance under different bending angles, and the assembled all-solid-state supercapacitor has good electrochemical properties.

Nanocarbon‐Based Hybrid Fillers in Thermally Conductive Polymer Composites: A Review

With the broad commercialization of microelectronics, 5G communication, and new energy vehicles, the demand for polymer composites with high thermal conductivity (TC) increases. Carbon‐based nanomaterials have high TC, are of lightweight and low cost, and have been widely studied as thermally conductive fillers for composites. In this article, carbon‐based thermal conductive fillers in polymer composites are focused on. It summarizes the treatments of functionalization, directional arrangement, and dispersion of carbon‐based nanofillers. Moreover, from the perspective of nanocarbon, hybrid nanofillers are divided into three categories: carbon/carbon, carbon/ceramics, and carbon/metal for the first time, and the thermal conductive effect of these hybrid fillers is discussed. Finally, potential areas for future research and development of thermal interface materials are discussed.

Conversion of Biopolymer to UV‐Cross‐Linkable Conductive Ink with High Conductivity, Biocompatibility, and Biodegradability

AbstractBiocompatible, sustainable, and conductive inks are of special interest and are highly valued in the printable bioelectronics. However, the conventional inks, which increase electrical conductivity by mixing metal particles or graphene, can cause long‐term damage when applied to the body and environment. Herein, a method for creating a stable matrix based on a UV‐cross‐linkable polymer to which a conductive polymer can be grafted is investigated to solve the above problems by recycling biomass. Through this, it is possible to achieve high conductivity using only biocompatible and sustainable polymers. Here, conductive inks for printable bioelectronics are developed by grafting polypyrrole on methacrylate‐modified sericin and poly(ethylene glycol) diacrylate (PEGDA). The highest electrical conductivity is achieved by adjusting the ratio of the pyrrole monomers polymerized on each polymer until the conductivity is optimized. Owing to the photoreactive nature of PEGDA, the prepared conductive inks are cross‐linked by UV light, thus giving them easy‐printing properties. The biodegradability, biocompatibility, and electrical properties of the printed patterns are systematically analyzed. This study has significant implications in the field of sustainable and printable bioelectronics as it has developed of a conductive ink with the biocompatibility, biodegradability, and high conductivity that is safer and simpler than conventional methods.

Artificial Muscles Based on Coiled Conductive Polymer Yarns

AbstractLightweight artificial muscles with large strain and large stress output have great application prospects in robotics, rehabilitation, prosthetic, and exoskeletons. Despite the excellent performance of carbon nanotube‐based artificial muscles in recent years, their widespread use is hindered by the high manufacturing costs associated with carbon nanotubes. In this paper, the study introduces a novel approach by developing artificial muscles based on pure conductive polymer coiled yarns. This achievement is facilitated by the successful fabrication of high‐strength conductive polymer microfibers. Furthermore, the study elucidates the molecular structural changes occurring during electrochemical processes that induce a substantial radial volume expansion in the microfibers. The resultant anisotropic volume change is magnified by the coiled yarn, yielding a remarkable contractile strain exceeding 11% at a high stress of 5 MPa, equivalent to lifting loads more than 4000 times their own masses, all achieved with a low input voltage of 1 V. Additionally, these conductive polymer‐based artificial muscles exhibit hydration‐induced contraction up to 33%, with swift recovery through electrical heating, leveraging their intrinsic high conductivity. This breakthrough positions high‐performance conductive polymer microfibers as a promising cost‐effective alternative to carbon nanotubes, establishing them at the forefront of lightweight artificial muscles.

Intercalating polypyrrole tuning interlayer space of V2O5 for advanced aqueous zinc ion batteries

Aqueous zinc-ion batteries is considered as a promising system for large scale electrochemical energy storage system owing to their intrinsic safety, and low cost. Nevertheless, the industrialization process is slow due to the constraints of high-performance cathode materials. Adjusting the layered structure of V2O5 through metal ion or polymer intercalation can effectively improve low electron conductivity, vanadium dissolution, and slow ion transport kinetics. Herein, the conductive polymer polypyrrole-intercalated V2O5·H2O (PVOH) was successfully prepared via simple hydrothermal method and following interface polymerization reaction. Getting benefit from the insertion of polypyrrole, the prepared PVOH composite material achieves a V2O5 cathode with a more open structure, rich active sites, and greater stability, allowing for an expanded crystal plane spacing of 14.5 Å. Therefore, the PVOH electrode demonstrates a discharge capacity of 475 mAh g−1 and a cycling stability of 95% capacity retention after 2000 cycles. The intercalating conductive polymers strategy can become a new approach to improve the electrochemical behavior of vanadium oxide cathodes.